首页 / 官方标准库 / 产品质量检验

官方标准 · 一单一库

产品质量检验

共 47,217 条标准

标准列表（第 1520 / 1574 页）

ISO3696:1987 分析实验室用水-规范和试验方法Water for analytical laboratory use - Specification and test methods

ISO3691-5:2014+Amd1:2020 Industrial trucks - Safety requirements and verification Part 5: Pedestrian-propelled trucks 工业车辆安全要求和验证第5部分:步行式车辆

ISO3691-4:2023 工业卡车.安全要求和验证.第4部分:无人驾驶工业卡车及其系统Industrial trucks - Safety requirements and verification - Part 4: Driverless industrial trucks and their systems

ISO3691-4:2020 工业车辆安全要求和验证第4部分:无人驾驶工业车辆及其系统stress-strain properties

废止，仅限能力项目库范围内现行有效产品标准引用本标准及监督抽检时申请...

ISO3690-2018 焊接碳钢和低合金钢手工焊熔敷金属扩散氢的测定Welding and allied processes - Determination of hydrogen content in arc weld metal

ISO3689:1983 纸和纸板-浸水后爆破强度的测定 Paper and board - Determination of bursting strength after immersion in water

废止，仅限能力项目库范围内现行有效产品标准引用本标准及监督抽检时申请...

ISO3688:2022 纸浆实验室纸页的制备蓝光漫反射因数(ISO亮度)的测定Pulps-Preparation of laboratory sheets for the measurement of optical properties - Third Edition

ISO3681:2018 涂料和清漆用粘合剂--皂化值的测定--滴定法Binders for paints and varnishes - Determination of saponification value - Titrimetric method

ISO3679:2022 闪燃､非闪燃和闪点的测定快速平衡闭杯法Determination of flash point - Method for flash no-flash and flash point by small scale closed cup tester

ISO3679:2004 闪点的测定-快速平衡闭杯法 Determination of flash point - Rapid equilibrium closed cup method

废止，仅限能力项目库范围内现行有效产品标准引用本标准及监督抽检时申请...

ISO3675:1998 原油和液体石油产品-密度的实验室测定-比重计法Crude petroleum and liquid petroleum products - Laboratory determination of density - Hydrometer method

ISO3668:2017 油漆和清漆油漆颜色的视觉比较Paints and varnishes - Visual comparison of colour of paints

ISO3651-3:2017 不锈钢耐晶间腐蚀的测定-第3部分:低Cr铁素体不锈钢的腐蚀试验Determination of resistance to intergranular corrosion of stainless steels - Part 3: Corrosion test for low-Cr ferritic stainless steels

ISO3651-2-1998 不锈钢耐晶间腐蚀的测定第2部分:铁氧体､奥氏体和铁氧体奥氏体(二重)不锈钢在含硫酸介质中的腐蚀试验Determination of resistance to intergranular corrosion of stainless steels -- Part 2: Ferritic,austenitic and ferritic-austenitic (duplex) stainless steels -- Corrosion test in media containing sulfuric acid

ISO3651-2:1998 不锈钢耐晶间腐蚀的测定第2部分:铁素体､奥氏体及铁素体-奥氏体(双相)不锈钢含硫酸介质中的腐蚀试验Determination of resistance to intergranular corrosion of stainless steels -- Part 2: Ferritic,austenitic and ferritic-austenitic (duplex) stainless steels -- Corrosion test in media containing sulfuric acid

ISO3651-1:1998 不锈钢耐晶间腐蚀的测定-第1部分:奥氏体和铁素体-奥氏体(双相)不锈钢-通过质量损失测量在硝酸介质中的腐蚀试验(休伊试验)Determination of resistance to intergranular corrosion of stainless steels -- Part 1: Austenitic and ferritic-austenitic (duplex) stainless steels -- Corrosion test in nitric acid medium by measurement of loss in mass (Huey test)

ISO362-2:2009 道路车辆加速行驶时发出的噪声测量--工程方法第2部分:L类 Measurement of noise emitted by accelerating road vehicles - Engineering method - Part 2: L category

ISO3613:2021 金属和其他无机涂层-锌､镉､铝锌合金和锌铝合金上的铬酸盐转化涂层的试验方法Metallic and other inorganic coatings - Chromate conversion coatings on zinc, cadmium, aluminium-zinc alloys and zinc-aluminium alloys - Test methods

ISO36:2020 硫化橡胶或热塑性橡胶与织物粘合强度的测定Rubber,vulcanizedorthermoplastic--Determinationofadhesiontotextilefabrics

ISO36:2011 硫化或热塑性橡胶纺织纤维粘合强度的测定Rubber, vulcanized or thermoplastic - Determination of adhesion to textile fabrics

废止，仅限能力项目库范围内现行有效产品标准引用本标准及监督抽检时申请...

ISO3506-7:2024 紧固件耐腐蚀不锈钢紧固件的机械性能第7部分:规定等级和性能等级的平垫圈Fasteners-Mechanical properties of corrosion-resistant stainless steel fasteners-Part 7: Flat washers with specified grades and property classes

ISO3506-4:2009 耐腐蚀不锈钢紧固件的机械性能第4部分:自攻螺钉Mechanical properties of corrosion-resistant stainless steel fasteners - Part 4: Tapping screws

废止，仅限能力项目库范围内现行有效产品标准引用本标准及监督抽检时申请...

ISO3506-3:2009 耐腐蚀不锈钢紧固件的机械性能第3部分:紧定螺钉及类似的不受拉应力的螺纹紧固件Mechanical properties of corrosion-resistant stainless steel fasteners - Part 3: Set screws and similar fasteners not under tensile stress

废止，仅限能力项目库范围内现行有效产品标准引用本标准及监督抽检时申请...

ISO3506-2:2020 紧固件耐腐蚀不锈钢紧固件的械性能第2部分:规定组别和性能等级的螺母Fasteners - Mechanical properties of corrosion-resistant stainless steel fasteners - Part 2: Nuts with specified grades and property classes

ISO3506-1:2020 紧固件耐腐蚀不锈钢紧固件机械性��第1部分:规定组别和性能等级的螺栓､螺钉和螺柱Fasteners - Mechanical properties of corrosion-resistant stainless steel fasteners - Part 1: Bolts, screws and studs with specified grades and property classes

ISO3497:2000 金属覆盖层覆盖层厚度测量X射线光谱方法Metallic coatings -- Measurement of coating thickness -- X-ray spectrometric methods

ISO349:2020(E) 烟煤奥阿膨胀计试验This document specifies a method for determining the swelling properties of hard coal when heated under standard conditions in a dilatometer Hard coal - Audibert-Arnu dilatometer test

ISO3471:2008 土方机械滚翻保护结构实验室试验和性能要求Earth-moving machinery -- Roll-over protective structures -- Laboratory tests and performance requirements

ISO3452-2:2021 无损检测渗透检测第2部分:渗透材料的检测Non-destructive testing - Penetrant testing - Part 2: Testing of penetrant materials

仅限非特种设备检测...

ISO3452-1-2021 无损试验渗透试验第1部分:总则Non-destructive testing - Penetrant testing - Part 1: General principles

仅限非特种设备检测...

上一页 1518 1519 1520 1521 1522 下一页

需要产品质量检验检测服务？

腾树检测合作实验室具备 CMA/CNAS 双重资质，专业高效

电话咨询 17602199916 在线获取报价